Experience with every opener type
More than 10 years of company experience and over 5,000 completed jobs across the Denver metro, from simple remote reprogramming to full opener replacement.

Bolt Garage Door Repair · Denver metro
Bolt repairs garage door openers across the Denver metro, diagnosing the motor, remotes, keypads and safety sensors together before explaining the work your opener needs.
Why choose Bolt
More than 10 years of company experience and over 5,000 completed jobs across the Denver metro, from simple remote reprogramming to full opener replacement.
Bolt inspects the opener and the door together as one connected system, so an opener repair corrects the actual fault instead of masking a symptom.
You receive the opener diagnosis, proposed parts, labor and the applicable warranty terms in writing before any repair is approved.
USA-made hardware can be requested alongside opener parts, and Bolt is reachable around the clock when an opener leaves the door stuck or unsafe.
Opener force settings and the safety sensors that reverse the door are tested by trained technicians, and the door's balance is checked after the work.
Bolt focuses on residential garage door opener repair across Denver and the surrounding metro, so you work with the same local team from first call to final test.
When to call
A dead opener, a failed remote and a door that is simply too heavy for the motor can all look the same from the driveway, but they need different repairs. Tell us whether the motor makes any sound, whether the wall button works when the remote does not, and whether the door is open or closed. A photo of the opener label can help identify the unit; it does not replace an on-site check.
An inspection looks at the power supply, wall control, logic board, drive mechanism and the safety sensors, then confirms the door itself is balanced. Symptoms are evaluated together. For example, a new motor will not fix a door that binds because the springs are worn, and reprogramming a remote does not help when the sensors are blocking every close.
When a door works from one control but not another, the opener motor is usually fine and the problem is in how it receives the signal. A remote may need a fresh battery or reprogramming, a keypad may have a worn code or entry pad, and a wall button can fail on its own wiring. We confirm which controls respond before replacing anything.
If every control is dead at once, we look past the handsets to the receiver, the antenna and the power at the outlet. Reprogramming is often the fix, but a control that keeps losing its code or a keypad exposed to years of Denver weather can point to a part that should be replaced rather than reset again.
The two photo-eye sensors near the floor stop the door from closing on a person, pet or vehicle. When the door starts to close and then reverses, a bumped bracket, a dirty lens or a loose wire is a frequent cause. We check that both sensors face each other, that their indicator lights are steady and that nothing in the opening is breaking the beam.
Sensor faults and force or travel settings are related but not the same. A door that reverses only near the floor can be a limit or down-force adjustment rather than a sensor, so we confirm the real cause before changing a setting. These safety features are never bypassed to make a door close.
Inside the opener head, a worn drive gear, a slipping belt or chain, or a failing motor can leave the unit humming without moving the door. We listen to what the motor does, watch how the carriage travels and check whether the trolley has released, so the repair targets the part that actually failed instead of swapping the whole unit by default.
Travel and force limits tell the opener how far to move and how hard to pull. When they drift, a door can stop short, slam down or reverse for no clear reason. We reset these to the opener manufacturer's procedure, and when a motor or logic board has reached the end of its life we explain why replacement is the honest call before you spend on repeated repairs.

Whether the fault is the opener, a control or the door itself
Parts, labor and any repair versus replacement choice
Safety sensor, force and travel-limit tests after the fix
Written warranty terms and contact details
Pricing, available parts and warranty coverage depend on the proposed work. Request the details in writing before you approve an opener repair or replacement.
The motor can run while the trolley is disconnected or a drive gear, belt or chain has failed. Pull the emergency release and test the door by hand; if it is heavy or binds, the spring system needs attention rather than the opener.
Yes. We reprogram remotes and keypads to the opener, replace worn handsets, batteries and entry pads, and set up new controls. If a control keeps losing its code we check the receiver, not just the handset.
Usually a safety sensor is misaligned, dirty or unplugged, or the close-force and travel limits need adjusting. We find the actual cause and never bypass the sensors to force the door shut.
We compare the failed part, the age of the unit and whether its safety features can be brought up to standard. A single part often fixes a sound opener, while repeated failures or an obsolete board can make replacement the better value.
Bolt services common residential openers, including LiftMaster, Chamberlain and Genie. For model-specific programming and limit settings we follow the manufacturer's procedures.
Bolt serves the Denver metro area, including Lakewood, Arvada, Aurora and Littleton. Confirm availability for your address when booking.
Our services
Google reviews
Selected excerpts from reviews of Bolt Garage Door Repair on Google.
Service area
Bolt Garage Door Repair helps homeowners throughout Denver and the surrounding metro. Choose your community to explore repair services and request an appointment.
View all Denver metro city pagesHow an opener repair works
Tell us what the opener does, whether the motor makes any sound, and if a vehicle is trapped inside.
A technician checks the motor, drive, controls and safety sensors, and confirms the door itself is balanced.
You receive the diagnosis and a written estimate with parts, labor and warranty before work begins.
Approved work is completed, then the sensors, force and travel limits are tested before we leave.
Repair or replace
Most opener faults are repairs, not replacements. Here is how to tell which path fits your opener, with a written Bolt estimate to confirm the cost either way.
Talk to Bolt
Include your city, the door's position and any visible damage. Confirm the appointment window and service-call details before booking.
720-500-7199Open 24/7